仿石路沿石也稱謂：仿大理石路沿石、路邊石、路緣石等。是采用濕法成型工藝進行胚體成型，經過一段時間養護，胚體強度達到一定要求后經過切割、打磨、拋光或拋丸處理。

Imitation stone curbstones are also known as: imitation marble curbstones, curbstones, curbstones, etc. It is a wet forming process used for embryo formation. After a period of curing and reaching a certain strength requirement, the embryo is cut, polished, polished or shot blasted.

仿石路沿石、路邊石、界石具體成型工藝如下 ：

The specific molding process for imitation stone curbstones, roadside stones, and boundary stones is as follows:

一、仿石路沿石（PC路沿石）胚體成型的配料過程：

1、 The batching process for the formation of the embryo of the imitation stone roadside stone (PC roadside stone):

仿石路沿石主要原材料為砂、細石、高標號水泥及無機氧化鐵顏料、添加劑、水等。根據生產的仿石產品的花色及強度要求的不同，配方有較大的區別，如何生產出優質的、讓客戶滿意的仿石產品需要生產企業進行反復的配方試驗。

The main raw materials for imitation stone curbstones are sand, fine stones, high-grade cement, inorganic iron oxide pigments, additives, water, etc. According to the different color and strength requirements of the produced imitation stone products, there are significant differences in the formula. How to produce high-quality and customer satisfied imitation stone products requires the production enterprise to conduct repeated formula tests.

二、仿石路沿石（PC路沿石）胚體成型過程：

2、 Imitation stone roadside stone (PC roadside stone) embryo forming process:

仿石產品一般采用濕法成型工藝。

Imitation stone products generally use wet molding technology.

這里講的濕法是和傳統上透水磚生產所用的干硬性產品生產工藝相對應的，透水磚產品生產時，生產所需原材料攪拌及成型過程中材料中的含水率極低，所以生產出的產品稱為干硬性混凝土制品。

The wet process mentioned here corresponds to the traditional dry and hard product production process used in the production of permeable bricks. During the production of permeable brick products, the moisture content of the raw materials required for mixing and forming is extremely low, so the products produced are called dry and hard concrete products.

濕法生產是在攪拌、成型過程中所有材料的含水率接近于傳統的混凝土工藝。

Wet production is a process in which the moisture content of all materials during mixing and molding is close to that of traditional concrete processes.

在成型過程中采用壓濾工藝將材料中的水份擠出，成為一種含水率極低的、近似于干硬性產品的制品。

During the molding process, the water in the material is squeezed out using pressure filtration technology, becoming a product with extremely low moisture content that is similar to a dry and hard product.

三、仿石路沿石（PC路沿石）胚體養護：

3、 Imitation stone road edge stone (PC road edge stone) embryo maintenance:

成型后的產品要放在養護窯內根據工藝要求進行充分的養護，這對后期的質量有直接的關系。

The formed product should be placed in a curing kiln for sufficient curing according to the process requirements, which is directly related to the quality of the later stage.

四、仿石路沿石（PC路沿石）胚體加工流程：

4、 Process flow of imitation stone roadside stone (PC roadside stone) embryo:

養護結束后的產品，當強度達到一定要求后進行到后期的加工過程中，加工分為粗加工、細加工及上光等幾個流程，根據對產品的不同要求來制定加工流程，各加工企業可根據自家不同的要求制定各自需要的加工流程。但粗加工流程是不可缺少的。

After the maintenance of the product, when the strength reaches a certain requirement, the processing is divided into several processes such as rough processing, fine processing, and polishing. The processing flow is formulated according to different requirements for the product, and each processing enterprise can develop their own processing flow according to their different requirements. But the rough machining process is indispensable.

五、碼垛流程：

5、 Stacking process:

這是生產過程中**后的一個流程。生產出來的產品重量一般在幾十公斤以上，且產品經過粗、精加工后，外觀品質已不同于一般的混凝土，需要在交付給客戶前，對產品外觀進行一定的保護，減少入庫、運輸及交付過程中對產品外觀造成不必要的破壞。

This is a post production process. The weight of the produced products is generally over tens of kilograms, and after rough and fine processing, the appearance quality of the products is different from that of ordinary concrete. Before delivery to the customer, it is necessary to protect the appearance of the products to reduce unnecessary damage to the appearance during storage, transportation, and delivery.

本文由山東仿石路沿石提供幫助，更多的相關內容請點擊： http://www.doushigroup.com 希望本文能夠?yàn)槟鷰?lái)幫助，感謝您的閱讀！

This article is provided by Shandong Fangshi Road Edge Stone for assistance. For more related content, please click: http://www.doushigroup.com I hope this article can be helpful to you. Thank you for reading!