When the curbstone is processed, it is a square prism, and many of the curbstones we see have a bevel or rounded corner, which is the chamfer we will talk about below.

倒角指的是把棱角切削成一定的斜面，那么路沿石是怎么來進行倒角的呢？小編介紹，路沿石倒角的方式有很多種，比較..的有全自動倒角的，然后還有半自動倒角的和人工倒角的。全自動倒角是利用的專門的倒角機來進行的，設置好參數之后就可以自動工作了，不過這種機器使用的廠家并不是很多，一來是比較的占地方，二來是使用率不高。

Chamfering refers to cutting edges and corners into a certain slope, so how does the curbstone chamfer? The editor introduces that there are many ways to chamfer curbstones, and there are There are fully automatic chamfering, followed by semi-automatic chamfering and manual chamfering. Fully automatic chamfering is carried out using a specialized chamfering machine. After setting the parameters, it can automatically work. However, this type of machine is not widely used by many manufacturers, as it takes up a lot of space and the usage rate is not high.

現在大部分的石材廠并不是只做路沿石的，通常既做各種的火燒板、光板、荔枝面等板材，又做各種路沿石的。因此大部分石材廠還是采用半自動和人工倒角的方式居多。所謂的半自動指的就是利用紅外線切割機來進行倒角，在加工路沿石的時候先把毛石切割成所需要的厚度，然后用切機切割成所需規格，..調整鋸片的傾斜度就可以倒角了，當然這種方式只適合倒斜角而不能倒圓角

Nowadays, most stone factories do not only produce roadside stones. They usually produce various types of fired boards, polished boards, lychee noodles, and other materials, as well as various types of roadside stones. Therefore, most stone factories still use semi-automatic and manual chamfering methods. The so-called semi-automatic refers to the use of an infrared cutting machine for chamfering. When processing curbstones, the rough stones are first cut into the required thickness, and then cut into the required specifications using the cutting machine Adjusting the inclination of the saw blade allows for chamfering, but this method is only suitable for chamfering and cannot be used for rounding

人工倒角應用的..多的就是倒圓角了，一般1-2cm的1/4圓角是..做的，只要用磨機蹭一下就能夠完成了，而..難的就是5cm左右的大圓角了，這種的圓角需要工人一點點的磨出來，而且在磨的時候還必須..統一的弧度，否則路沿石沒法排列整齊。

For manual chamfering applications There are many rounded corners, usually 1/4 rounded corners of 1-2cm are It can be done by just rubbing it with a grinder, and The difficult thing is the large rounded corner of about 5cm, which requires workers to grind it out bit by bit, and during the grinding process, it must also Uniform curvature, otherwise the curbstones cannot be arranged neatly.